Material Download for TS100 Smart Soldering Iron

minidso · 发表于 2015-8-3 15:58:44

2022.01.11 Update:
2017.11.24 Update:TS100 APP 2.20:

TS100 APP V2.20.zip (33.55 KB, 下载次数: 9278)
-Fixed the problem of missing hardware ID for individual chip U disk identification
-Add compatible GD chip
- Modify the comment range of U disk parameters
-Enhanced U disk parameter recovery ability

2021.08.25 Update:
TS100 Soldering Iron User Manual V1.1 : http://forum.minidso.com/forumdo ... aul%20V1.1%20EN.pdf

2020.08.05 Update:
TS100 Solering Iron User Manual V1.0.3 : http://forum.minidso.com/forumdo ... l%20V1.0.3%20EN.pdf

TS100利用者マニュアル V1.0.2バージョン:

TS100利用者マニュアル V1.0.2バージョン.pdf (5.9 MB, 下载次数: 17494)

TS100 open-source release:
2017.11.24 Update:TS100 APP 2.18：

TS100 APP V2.18.zip (33.38 KB, 下载次数: 32336)
TS100 APP 2.18 Source Code files：

TS100_V2.18_Source_Code.zip (639.13 KB, 下载次数: 15261)
-Increase the initialization of LIS2DH12 accelerometer, and perform power-on judgment to select the correct accelerometer model for configuration

2017.5.12 Update:TS100 APP 2.17:

APPV217.rar (34.08 KB, 下载次数: 16731)
TS100 APP 2.17 Source Code files:

TS100_V2.17_Source_Code.zip (253.81 KB, 下载次数: 8298) (Note：Base on IAR 6.4)
- Solve the problem of version number display;
-Optimize switching to left-handed mode (A/B keys will also correspond to left-handed mode adjustment);

2017.5.9 Update:

TS100 Мини паяльник Инструкция Версия 1.0.1.pdf (9.37 MB, 下载次数: 12741) переводчик : Кирилл Ткачук

2017.4.28 Update :
TS100 APP 2.16:

APPV216.rar (33.1 KB, 下载次数: 10861)
- Expanded the range and accuracy of the protection voltage, which can be accurate to 0.1V;
- The first item is fixed to temperature adjustment and voltage display after entering setting mode from standby mode;
-In the setting mode, long press any key to enter the parameter adjustment of the selection item, add the double key long press to exit function;
- Added when the TempStp step size is set to 1, the temperature setting long press has a quick modification effect.

TS100 APP 2.12:

APPV2.12.zip (33.62 KB, 下载次数: 12882)
TS100 APP 2.12 Source Code files:

TS100_V2.12_Source_Code.zip (569.26 KB, 下载次数: 7715) (Note：Base on IAR 6.4)
- Set temperature can be saved
- increase the maximum voltage of the alarm;
- Newly added screen saver function, after entering the standby interface for a period of time, the screen will turn off by itself, and the screen will automatically light up when you press a button or move the soldering iron;
- Cancel the function of entering the thermometer when powered by USB;
-Optimized reading and writing of U disk

TS100 Source File Description---Control Managerment：

TS100 Source File DescriptionControl Managerment.pdf (351.08 KB, 下载次数: 11693)
TS100 Source File Description-- Interface Management：

TS100 Source File Description Interface Management.pdf (5.32 MB, 下载次数: 11968)

TS100 V2.46 Schematics V1.0:

TS100 V2.46 Schematics V1.0 .pdf (22.38 KB, 下载次数: 20778)

TS100 Soldering Iron Instruction Manual :

TS100 Soldering Iron Instruction Manual.pdf (5.8 MB, 下载次数: 16266)

galaxy76 · 发表于 2020-6-7 23:49:05

qual è la differenza tra firmware 2.17 e 2.18?

FreeMaxl · 发表于 2017-5-11 16:19:11

[i = s] posts by FreeMaxl in 2017-5-11 16:32 Edit

minidso Posted 2017-5-11 09:39
We will soon release app V2.17, and source code of app V2.17

OK, first of all, You have done well good work on the Firmware ! Thank you.
So I just relax and wait for your V2.17 source-code release.

I just have some Ideas:

In Version 2.16 the Parameters for Sleep- and Idle-Time are (low)limited to 60 or 100 seconds.
I think its a good Idea to set the low-limits to 15 and 25 seconds. (if someone feels comfortable with short standby times)
(for myselfe I really often use the two-Buttons to switch-off the soldering Iron)

The Parameter "OffVolt" have an upper Limit from 12V:
I use the TS100 on my Motobike-travvels. So I want to protect Battery from discharge. Therefore the Parameter for "OffVolt" should be settable to higher Values. I think 16 V is a good upper Limit for this Parameter.
If the Source-Voltage gets lower then the "OffVolt" Setting the Display just resets.
I think its better when first a Message is printed on the Display "! Low-Volt !" and then a wait-time of 3 seconds bevore the program go further. (so that the message is readable) I think when the Voltage gets too low, a "global" wait-time is really ok. (because its a problem)

Maybe you want to change some of this in a possible 2.18 release. (or in 2.17 if it is not too much work)

RagnarKon · 发表于 2015-8-27 04:47:34

Do you have the .hex file?

I can not compile the source code. I do not have IAR 6.4.

dkov · 发表于 2015-12-19 03:55:05

Hello

I got two of this this super solder irons. They ar really great! But now one of them is not working properly... I can´t make the logo working. I upload a LOGOIN.bmp file and the space in the solder iron is smaller but after I start the iron, the old logo is visible. When I upload a new picture the space on the stick is smaller again... but it doesn´t work. The other one is working fine. I have made an fw upgrade... Please help. Thank you ;)

minidso · 发表于 2015-12-21 11:05:23

The logo file name must LOGOIN.bmp, and the details is:

Now if you TS100 does't work , You can try to upgrade the TS100 APP 2.11 .

yinyongqin · 发表于 2016-1-12 16:09:33

APPV211.zip

a6pam · 发表于 2016-8-5 20:57:08

本帖最后由 a6pam 于 2016-8-5 21:09 编辑

hello to all

recently I bought a iron soldering ts100. but it has not worked. . I disassembled and saw that one simply does not soldered capacitor. on electric circuit he have #23. tell him capacity. that I could find a replacement.

thx.

minidso · 发表于 2016-8-8 09:47:10

C23 is designed to be empty, so there is no capacity.
Could you explain how the soldering is not working? What does it display on the LED screen?
What power supply do you use? If you use 12V power supply, the current must be more than 1.5A.

a6pam · 发表于 2016-8-9 03:26:28

minidso 发表于 2016-8-8 09:47
C23 is designed to be empty, so there is no capacity.
Could you explain how the soldering is not w ...

I use 12V and 3A power supply.

When I click on the button immediately terminates heating.

for greater understanding link for video.

youtube link

Thx

minidso · 发表于 2016-8-9 09:30:12

a6pam 发表于 2016-8-9 03:26
I use 12V and 3A power supply.

When I click on the button immediately terminates heating.

Open config.txt
edit "Turn_Off_v=10 #(9~12)"
try turn_off_v=9

If TS100 still can't work. Please check your power supply, and recommend the use of 19V 2A power.

johncomp · 发表于 2016-8-24 23:18:47

Hello. you can do APPv212.hex for the left hand?

		自动登录	找回密码
密码			立即注册

[Firmware update] Material Download for TS100 Smart Soldering Iron

社区居民

忠实会员